Dave Hettmer
  • Male
  • Ann Arbor, MI
  • United States
Share

Dave Hettmer's Friends

  • Eduardo Salmar
  • Shea Street
  • Paul J. McConnochie
  • Ron Cole
  • Rick Catizone
  • Jeff Lafferty
  • Don Carlson
  • John Dods

Dave Hettmer's Discussions

Camera/Set mover

Started this discussion. Last reply by Chris Johnson Jul 27. 1 Reply

Here's a gizmo I recently built for someone who teaches stopmo at a university in PA.  It's a heavy-duty camera mover.  All those who saw it on the Facebook dot com dot net dot dot can ignore this…Continue

Rigging a cape

Started this discussion. Last reply by McKinlay Feb 15. 13 Replies

I'm rigging a small cape and looking for info from people who have done this before. The cape is about 5" long and is torn and ratty. So I can't hide wires in hemmed seams like I have in the past.I'm…Continue

3D Printer Review from Ars Technica

Started Aug 28, 2013 0 Replies

3D Printers are frequently in the stopmo news these days.  Here's an independent review of two consumer level models: Printrbot and Makerbot…Continue

Question on relief slots

Started this discussion. Last reply by patrick zung Apr 29, 2013. 6 Replies

Here's a shot of a joint I made recently.  It's OK, but I'm looking to make it better.The lower pivot can be tightened to the point where the gap is closed but the joint isn't as tight as I'd like.…Continue

 

Dave Hettmer's Page

Latest Activity

Dave Hettmer replied to Santino Vitale's discussion Monster Makers Foam -- New Mix Ratios
16 hours ago
Chris Johnson replied to Dave Hettmer's discussion Camera/Set mover
Jul 27
Dave Hettmer posted a discussion
Jul 13
Dave Hettmer replied to Spencer McCarlie's discussion Armature components
Jun 30
Dave Hettmer replied to StopmoNick's discussion Change to look of site?
Jun 30
Dave Hettmer posted photos
Jun 3
Dave Hettmer replied to Jason Whetzell's discussion Mystery Clay (Pro-Clay vs. Monster Clay)
May 21
Dave Hettmer replied to Jason Whetzell's discussion Mystery Clay (Pro-Clay vs. Monster Clay)
May 20
McKinlay replied to Dave Hettmer's discussion Rigging a cape
Feb 15
Simon Tytherleigh replied to Dave Hettmer's discussion Rigging a cape
Dec 15, 2014
Simon Tytherleigh replied to Dave Hettmer's discussion Rigging a cape
Dec 15, 2014
Dave Hettmer replied to Dave Hettmer's discussion Rigging a cape
Dec 9, 2014
Don Carlson replied to Dave Hettmer's discussion Rigging a cape
Dec 9, 2014
patrick zung replied to Dave Hettmer's discussion Rigging a cape
Dec 8, 2014
StopmoNick replied to Dave Hettmer's discussion Rigging a cape
Dec 8, 2014
Strider replied to Dave Hettmer's discussion Rigging a cape
Dec 8, 2014
PupCup replied to Dave Hettmer's discussion Rigging a cape
Dec 8, 2014
jowanneke replied to Dave Hettmer's discussion Rigging a cape
Dec 8, 2014
Dave Hettmer replied to Dave Hettmer's discussion Rigging a cape
Dec 8, 2014
StopmoNick replied to Dave Hettmer's discussion Rigging a cape
Dec 8, 2014

Dave Hettmer's Photos

Loading…

Comment Wall

  • No comments yet!

You need to be a member of StopMotionAnimation.com to add comments!

Join StopMotionAnimation.com

 
 
 

GUMBY FEST 2015

MESSAGE BOARD QUICK LINKS

Message Board

Light flicker in Nikon D5100

Started by Jacob Crow in CAMERA & STAGE. Last reply by Miles and Jules 2 hours ago. 4 Replies

Hi all,I'm currently encountering some light flicker issues while using the Nikon D5100 in Dragonframe.Sorry for the poor quality gif, but you get the picture. All the settings on the…Continue

Monster Makers Foam -- New Mix Ratios

Started by Santino Vitale in CASTING. Last reply by StopmoNick 6 hours ago. 4 Replies

Hello all,I'm not sure how many of you out there use Monster Makers foam latex -- for me, it's the ONLY foam I ever use and have recommended it highly over the years.... till recently.This past week, I bought a new quart kit for a project, and…Continue

Tags: gelling, bad, puppets, casting, makers

Steel Cut Oats

Started by Harry Chaskin in YOUR STOPMO FILM PROJECT. Last reply by Harry Chaskin yesterday. 15 Replies

Hello All! Wanted to let you know about a new short film I am making entitled Steel Cut Oats. I don't usually ask for help when it comes to my personal projects, but I finally bit the bullet and I'm launching a Kickstarter campaign in order to raise…Continue

Lookinbg for some stop motion dinosaurs

Started by John Martin in NEWBIE CORNER. Last reply by John Martin Jul 30. 4 Replies

I am a filmmaking veteran of 43 years. I began in 8MM and moved on with the times, now shooting in digital. I am not a professional. My very first film was a stop motion project called MONSTER ISLAND. To make a long story short, after 43 years, I am…Continue

Has anyone cast from polyamide 3d prints?

Started by Joshua Liebling in CASTING. Last reply by Joshua Liebling Jul 29. 2 Replies

Polyamide plastic will apparently break down with water exposure, so this rules out gypsum molds. I'm curious if anyone here knows whether two-part silicone putty or other material would work with polyamide? I know this can be done with PLA. My end…Continue

Tags: mold, making, polyamide, casting, printing

Lighting Equipment

Started by Krista W in ANIMATION TOOLS & EQUIPMENT. Last reply by StopmoNick Jul 29. 1 Reply

Hello, I recently received funding for my stop motion project.  I would like to purchase lighting equipment that I can use for this and future projects.  Any suggestions? Lighting is the one area that I don't know much about. Thoughts on dimmer? Any…Continue

BLOGS

Create a Blog for your personal page. Go to My Page and click on Blog Posts. Access all Blog Posts here.

Photos

Loading…

Members

© 2015   Created by Anthony Scott.   Powered by

Badges  |  Report an Issue  |  Terms of Service

.xg_widget_forum_index_index .xg_column.xg_span-7.xg_last {display:none;} .xg_widget_forum_topic_listForCategory .xg_column.xg_span-7.xg_last {display:none;} .xg_widget_forum_topic_show .xg_column.xg_span-7.xg_last {display:none;}